Just How to Install a Bathtub in Your Bathroom
Just How to Install a Bathtub in Your Bathroom
Blog Article
The content which follows involving Installing A Bathtub is unquestionably engaging. Read on and draw your own personal results.
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is conveniently easily accessible, the project can relocate easily; if you need to open up a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub as well as embeded in the new one. See to it you have certified yourself for the task and fit attempting it. Instead of employing a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will certainly help you set up a brand-new bathtub in your shower room if you have actually currently bought a new bathtub and also don't need to transform the setup of your previous supply of water pipelines.
Your tools and also product checklist must consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly problematic because of the limited accessibility that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin ensuring that the washers are in area in between the tap and the sink. Secure the tap in position with the maker provided backnut. As soon as the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Using both wooden boards under its feet, position the bath tub in the called for setting. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as changing the feet on the tub up until the spirit level reads level.
To install taps, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the supply of water and examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally inspect the overflow outlet and the regular outlet for leaks.
Finally, deal with the bath paneling as described in the supplier's instruction manual. Tiling as well as sealing around the tub should wait until the tub has actually been made use of at the very least when as this will settle it right into its final position.
Planning for the Setup
Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to ensure that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last placement.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the market. It is recommended to fit the tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on How to Install a Bathtub, I assumed sharing that post was beneficial. You should set aside a second to distribute this blog post if you enjoyed it. We treasure reading our article about Tools You Need to Install a New Bathtub .
Contact Us Now Report this page